Series F test frames with EasyMESUR® F755 / F755S / F1505 / F1505S

The Series-F motorized force testers are developed as a stand-alone measuring test frame, no Force Gauge or Indicator is required.

They come in two versions with integrated touch screens and one that is connected to your own windows computer.

For each version there are low load versions ranging from 0,5 to 2,5kN and higher load versions ranging from 3,4 to 6,7kN
The lower load ranges come in 3 vertical and one horizontal versions the higher load ranges come in 4 vertical versions.

The EasyMESUR® range has the smaller 7”display and comes in a basic setup.
It is equipped with 2 USB-C ports, one for PC connection and the other for an external flash drive.
Optional functions like Distance measurement, Distance limits, Pre-load, High speed extension. Low speed extension, cycling, break detection, load holding, FollowMe, graphing and reporting and PC control are available as single option, in packages or as a complete options package.

The IntelliMesur version of the Series-F motorized test stand is available with 10,1”screen or without screen for connection to PC.
It comes with all options from the EasyMESUR® as standard plus some extra features such as Overlay previous runs on graph and the option of COF measurement.

All devices are equipped with basic test wizards to guide you through a test setup.
There are options to extend the colums, add protective screens and a number of sensors in a range of loads compatible to the different test stands.
By using a PTAF adapter various customer supplied sensors can be used, the 705 series and up (3,4kN+) range needs an extra adapter.

The 7 inch control panel used with the EasyMESUR® can provide all kinds of data and has a number of specific features.

Control panel features The 7" tablet supports 2 USB-C ports for PC and external flash drive connection.	Standard view View load and distance values with clear, simple controls.
Graph view View a graph of load vs. distance or time, with pass/fail status.	Results view View results for each run, with corresponding statistics for the results.
	Secure user access Control user access to sensitive areas, such as test editing and calibration via password.

Plug & Test® sensors for Series-F

The Series-F works uses its own version of the Plug & Test® sensors. Available are the FS05, FS06 and the R07. All are used for compression and tension testing and use the operating systems of the test stands.
The FS05 is available in a capacity range from 0,5 to 2,5kN and connects directly to the F105, F305 and F505 range test stands. When used on the F755 and F1505 range an extra adapter, AC1083, is required.

Plug & Test® technology saves all configuration and calibration information within the adapters PCB. This flexibility allows for interchangeability between multiple sensors with any Mark-10 Series F test frame.

PTAF adapter

The PTAF connector is an adapter that can be used to connect 3^rd party strain gauge load cells, force- and torque sensors to the Series-F test stands. It can be connected directly to the F105, F305 and F505 range and via an extra adapter, AC1083, to the F755 and F1505 range, the M5I and the M7I indicators.
Sensor capacity and resolution may be configured via an included software utility, which includes a library of common force capacities from 0,5 N to 4.000 kN, and torque capacities from 7 Ncm to 57.000 Nm.
When an identification number is configured, it is displayed upon hardware power-up or the test stands display.

By removing the circuit board and side cover the third party sensor you can be connected to the PTAF adapter	Feed the cable through and connect the wires to the terminal block.
Replace the circuit board and side cover.	The sensor can now be configured using the included , Plug & Test Adapter Configuration software and used on the Series-7 test frame. An extra adapter (AC1083) is required to connect the PTAF to the F755(S)/F1505(S) range test frames.